Product Overview
The True TPP-AT-60D-2-HC is a 60-1/4" pizza prep table built to keep a prep station moving through a full service. True's patented forced-air design holds both the pans on top and the cabinet below between 33°F to 41°F, so product in the rail stays as cold as product on the shelf and the top does not creep warm during a rush.
The deep 19-1/2" cutting board gives a pizza maker room to stretch and dress a pie without crowding, and the refrigerated base below swallows dough boxes and backup toppings. The board lifts off in one piece for washing.
Drawers replace the lower door section, so a cook pulls product straight out at waist height instead of crouching and reaching. Each drawer rolls on heavy-duty slides and seals against a magnetic gasket. The exterior is stainless steel front, top and ends over a clear-coated aluminum liner with a stainless floor and coved corners, and the condensing unit slides out from the back for service.
Product Details
- True® 60-1/4" pizza prep table
- Patented forced-air design holds 33°F to 41°F in both food pans and cabinet interior
- Complies with ANSI/NSF-7 for open food product
- R290 hydrocarbon refrigerant — zero ODP, 0.02 GWP
- Self-contained capillary tube system, factory balanced with guided airflow
- Low-velocity, high-volume fan with sealed, self-lubricating motor
- Condensing unit accessed from the back on a slide-out mount
- Epoxy-coated evaporator resists corrosion
- Each drawer holds two full-size pans (12" L x 20" W x 8" D), sold separately
- Removable cutting board — 19-1/2" D x 1/2" thick, full length, removable white polyethylene
- Heavy-duty drawer slides rated for constant commercial service
- Magnetic drawer gaskets seal cold air in the cabinet
- Stainless steel front, top and ends; GalFan-coated steel back
- Clear-coated aluminum interior liner, stainless steel floor with coved corners
- High-density polyurethane insulation foamed in place (zero ODP, zero GWP)
- 1 solid door and 2 drawers with stainless exterior and aluminum liner
- One-piece magnetic gaskets, removable without tools
- Drawer storage in place of lower shelving
- Factory pre-wired with cord and NEMA 5-15P plug
Dimensions & Utilities
| Specification |
Detail |
| Cabinet Dimensions (W x D x H) |
60-1/4" W x 33-5/8" D x 38-7/8" H |
| Pan Capacity |
Each drawer holds two full-size pans (12" L x 20" W x 8" D), sold separately |
| Doors & Drawers |
1 solid door and 2 drawers |
| Shelving |
Drawer storage in place of lower shelving |
| Cutting Board |
19-1/2" D x 1/2" thick, full length, removable white polyethylene |
| Temperature Range |
33°F to 41°F |
| Electrical |
115V / 60 Hz / 1 Phase |
| Amps |
3.9 amps |
| Plug Type |
NEMA 5-15P (15 amp dedicated outlet recommended) |
| Refrigerant |
R290 Hydrocarbon (zero ODP / 0.02 GWP) |
| Cord Length |
10 ft. |
| Unit Weight |
415 lbs. |
Additional Product Information
-
Approvals & Certifications: Made in USA, cUL, NSF/ANSI 7 (Open), CE, Natural Refrigerant (R290).
-
Optional Accessories: 6" standard or seismic/flanged legs, 2-1/2" castors, additional shelves, single or double overshelf, flat lid, sneezeguard, composite cutting board, pan dividers and factory-installed exterior digital temperature display are available. Upcharges and lead times may apply.
-
Optional Electrical: 230-240V/50Hz or 208-230V/60Hz available on most models. Upcharge and lead times may apply.
-
Installation Requirements: Requires a dedicated 15 amp, 115V circuit. Allow clearance at the rear for condensing unit access. Commercial installation only; not intended for home or residential use.
